Jun 18, 20213 min read

Half Hexi Tote Bag Tutorial

My husband recently bought himself a new toy in the form of a 3D printer. So, I have been thinking of ways that I can make the most of it in my sewing room and have tried out a few quilting templates. We have tried a few different designs and shapes including this half hexagon. I saw a cheat hexi quilt years ago and always wanted to give it a go so I thought this shape would be a great place to start.

I was sent some new fabrics from The Craft Cotton Company to play with that are garden themed. They have wellies, bee hives, watering cans, hedgehogs and plant pots. My neighbours also have their own business and pre Covid we used to do our daily post runs together. Our chats now are confined to the garden fence and since she had a special birthday recently, I thought I would try out the new hexagon template in a bag to help carry some of her packages.

YOU WILL NEED

Hexagon template
Fat quarter bundle
Half metre for lining
Rotary cutter and mat
Iron and ironing board
Wadding
1m bag strap
Sewing machine
Scissors

METHOD

First cut your fabric. I have used my new template which you can purchase here. I first cut 3" strips vertically and then used the template to make the hexagon shape. If you don't have a template you could create your own with some card. I would suggest creating a hexagon on something like Word that is 6" wide, print it, cut it in half and then transfer it to card

White Beehives - 24
White Wellies - 24
Yellow - 10
Green - 12
Hedgehogs - 10

2. Layout your fabric. I have laid it out in a way that means the hexagons will be complete on the seam.

3. Sew the vertical rows together. When you pair the pieces up, make sure you don't meet the corners, there needs to be a 1/4" gap. Use a 1/4" seam allowance.

When they are sewn together, give them a good press. I press my seams open.

4. Then sew the columns together and trim the edges.

5. I have used Bosal Mid-Weight wadding to give the bag some strength. Pin the fabric to the wadding and quilt however you like. I have gone with diagonals through the centre of the hexagons.

At this point I realised my dimensions didn't look quite right so I had two options - trim it or turn the top over. Since I didn't have any multidirectional fabric left for the lining I went with the trim it option. I trimmed 2" off so that the top hexagon was in half.

6. When you have done both sides, pin them right sides together around the sides and bottom edge and sew. I was recently asked to try out some Clover Fork Pins through UK Quilters United (if you were wondering what was different about the pins). You can read what I thought about them here.

7. To make the bottom square you need to fold the corners so that the side and the bottom edge meet. Measure 3" from the point and mark it with pins or a dissolvable pen. Sew across, back stitch at the start and finish. Trim off the excess.

8. I wasn't very smart when I cut my fabric so I didn't have any of the designs wide enough to line my bag. No worries though, I just pieced two of the fabrics together and I am actually pleased that I did. Each finished side needs to be 19" x 21".

9. I added a pocket to the inside by cutting a 12" x 6" piece of the hedgehog fabric. Press over the top edge by 1/4" twice and top stitch. Press over the remaining three edges by 1/4". Pin it the the centre of the lining, around 3" from the top and top stitch it in place.

10. Repeat steps 6 and 7 with your lining pieces but leave an opening around 3-4" wide on one of the sides to turn it out through.

11 I have used 34mm grey webbing for the straps. You could do the same or make your own straps in the fabric. The strap on each side is 50cm. Pin it one hexagon in from each side and top stitch in place.

12. Turn the lining the right way round and place it inside the main bag so that the right sides are together. Pin it with the side seams matching and then sew it all the way around the top edge. Backstitch over the straps to reinforce it.